Furniture listing

• • Auto reverser

• • Circuit breaker

• • Automatically control reverse loop turnouts

• • Accessroy decoder for turnout solenoid motors:
    • • Kato
    • • Peco
    • • Atlas

• • Block Detection

• • Network Status Feedback

• • Outputs for LED Indicators: Remote LEDs can be added to monitor the input/output power and the status.

• • 4 Indicator LEDs on the board: Booster power (green), 2 x Block power (green), Block shorted (red)
    • • LED output DCC power in from booster
    • • LED output DCC power out to track/LED output turnout position/track phase  
    • • LED output short circuit
    • • LED output block occupied

• • Select Trip current values 1 – 10 in integer steps (1, 2, 3, …., 10) using CV 49

• • Jumper Select Current limits of 1, 2, 3, or 4 amperes

• • Power On/Off by DCC: Turn on/off output track power with your DCC Throttle!

• • Manual or Automatic Reset: Automatic reset: Breaker tries to reset every 2 seconds. Manual reset: Once the breaker trips, it remains off, ensuring complete isolation of the faulty block. The breaker is reset either by a switch or by a DCC command.

• • All Solid State Operation: Fast, solid state design with reliable quiet action.

• • Adaptive Load Reset: Electronically determines if the overload is a real short or due to excess capacitance in sound decoders or lighted passenger cars.

• • Auto Stop with DCC Reset: A photocell can be connected to a PSXX input. Normally, covering the photocell will not cause any action. If the photocell is armed with a DCC command, the PSXX will turn off the next time the photocell is covered. A DCC command can restore the track power when desired.

• • Photo Cell Controlled Block Power Off: Stop position control and occupancy detection for hidden tracks.

• • Block Detection: Either a photo cell or block current draw can be used to detect a train in a block and to trigger a Block Occupied output. The current trigger level is programmable.

• • Block Occupied Trip point can be automatically set to compensate for current flow in unoccupied block

• • Very Low Voltage Drop: Total breaker on resistance is less than 0.060 ohms, so the PSXX has a very low voltage drop even at high currents. Better than detectors that use a diode voltage drop.

• • Programmable Power Up Status: When power is applied to the layout, the PSXX can be set to always turn on, always remain off [power on as needed by DCC command], or to use the power status present when the layout was last shut down.

• Network Feedback: Isolated outputs designed to provide Block Occupied, Block Shorted, and Power Status to a discrete interface for remote display or computer control.
  • Will work with Digitrax LocoNet, NCE Cab Bus, ESU ECoS, and Lenz XpressNet interfaces.
  • • System Reset: CV63=42 sets all CVs and addresses to original factory values.
    • Output for Audio Alert: An audible sounder can be added to the PSXX to provide an audible alert if there is a short.
    • No Power Supply Needed: The PSXX uses the track DCC power to supply its operating power. Each PSXX draws less than 0.04 amperes.
    • Easy to Install: With 4 mounting holes sized for a #6 screw.
    • Flash Programmable: The PSXX firmware can be updated by Tony’s Train Exchange as new features become available or if older units need to be matched to a recent purchase.
    • Discrete Input allows on/off control of track voltage for yard or other track section isolation. Compatible with any system that has a relay or isolated transistor control output including LCC, WiFi, etc. or can be used with manual toggle switch.
    • +5V and Ground Outputs for powering LEDs, no resistors needed
    • Power On Status can be on, off (yard or staging sections), or status at power down.

• Plug and Play Universal fascia panel supporting LocoNet.
• Two RJ12 front panel Throttle jacks.
• Three RJ12 rear pass-through LocoNet jacks
• Supports throttle charging.
• Fully connectorized installation.
• 2mm rear plug for e.g. PS14 DC power supply.
• 4-pin rear plug option to share DC power.
• Track Status LED.
• Updated design.
• Replaces UP5 LocoNet Universal Interconnect Panel.

• Fascia mount Switch control device.
• Wire to DS74 input cable, or use DSXC4 for plug and play.
• Two color leds display current Switch state.
• Supplied with 3 wire control cable.

• Bracket will hold: DT602, UT6 and other legacy Digitrax throttles.
• Access to LocoNet & Power Ports when stowed away.
• Stores throttle when not in use or when charging.
• Fascia mounted.
• Durable design.
• Easy to install.
• 90 Day Warranty On Materials & Workmanship Only.
• 4-Pack

• Bracket will hold: DT602, UT6 and other legacy Digitrax throttles.
• Access to LocoNet & Power Ports when stowed away.
• Stores throttle when not in use or when charging.
• Fascia mounted.
• Durable design.
• Easy to install.
• 90 Day Warranty On Materials & Workmanship Only.

Realistic Slow Motion Turnout Operation, Now With Organic DCC!

• Prototypical slow-motion action - three seconds to complete throw
• Adjustable throw speed
• Precision-engineered gear drive mechanism
• Simple mounting with linkage included - no additional brackets or linkage necessary
• Convenient auxilliary contacts: two built-in SPDT switches can control signals, control panel lights or other electical accessories