DCC Booster board without the power supply. These boards can be used to make locomotive Power Districts or an Accessory District with a shared power supply. A jumper is used to set either Accessory Mode or Power District Mode. Each board can supply up to 3 Amps continuous duty and 5 Amp peak with a suitable power supply. These boards work very nicely with the Hex Frog Juicer.
Max power supply voltage: 40V
Power Connector: 5.5 mm (outer)/ 2.1 mm (inner) barrel plug, center positive
DCC input: optically isolated, 5-24 Volts (voltage level on the DCC input pins has no effect on output voltage level), 25 mA load typical.
DCC Connectors: Screw blocks
Max output: 5 Amps for short periods, 3 Amps continuous
Peak-to-peak output voltage: Power Supply voltage minus 0.8-1.4 volts (decreasing with load and independent of voltage on the DCC input)
Short Trip Point: 5.6 Amps
Short Trip Off Time: 1 microsecond
Short Trip Recovery Time: 200 microseconds
No Auto-reverse
Board Size: 3" long x 2.5" wide x 0.5" deep (including heatsink) (76mm x 64mm x 12mm). Green blocks extend another 0.3" (8mm).
The Pololu Pushbutton Power Switch is a patented design initially created for our Orangutan Robot Controllers as an alternative to bulky mechanical switches. The switch is intended to be the main power switch for a DC device requiring up to several amps of current.This item is the 4.5-20 V standard-voltage version.
16V 5A Power Supply for Larger Scale Track Power Use
16V 5A 80W switching power supply. Voltage is a little high for HO scale, but may be used if you take the risk. Good for larger scale track power. Delivers about 15V to track when used with TVD-DAB002 Booster. Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug. By swapping the power cord can be used with 100-240V~50/60Hz power. If you add the TVD-JCK001 screw terminal adapter you can use this as a general purpose power 16V supply.
14.5V 5A Power Supply for HO Scale Track Power Use
14.5V 5A 72.5W switching power supply. Best for HO track power. Delivers about 14.2V to track when used with TVD-DAB002 Booster. Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug. By swapping the power cord can be used with 100-240V~50/60Hz power. If you add the TVD-JCK001 screw terminal adapter you can use this as a general purpose power 14.5V supply.
12V 5A Power Supply for N Scale Track Power and Accessory Bus Use
12V 5A 60W switching power supply. Best for powering N scale, Quads, and Singlets. Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug. By swapping the power cord can be used with 100-240V~50/60Hz power. If you add the TVD-JCK001 screw terminal adapter you can use this as a general purpose power 12V supply.
TurnOn Module - Soft Start Circuit For Large Inrush Currents of Sound Decoders and Stay Alive Decoders
If you have a lot of sound decoders and decoders with stay alive circuits on the track, they can confuse the booster when it starts up in to thinking there is a short because of the sudden current draw of all the capacitors. This circuit prevents that problem by putting a small resistance in to the circuit to slow the current rush and once the voltage gets up a 10 Amp relay bypasses the resistor so that there is a straight connection to the booster. If you have no idea what the previous explanation about and you are not having any touble with starting your layout then you don't need the TurnOn.
Connect the TurnOn directly after the booster and before any other components.
Resistor is 0.5 Ohms 20Watt. Relay is 10 Amps and turns on at about 10Volts on the track. Diodes prevent the startup pulse of the relay from getting on to the DCC bus.
Will also work with other brands of boosters and command stations.
You can now add layouts you create in the Shop Admin into any post or page. To make it simple a Shortcode Generator is included. You can access it via this button.
The first button is the shortcode genreator launcher and the second one ( the one with a plus ) ads a single audio player to the page from the media gallery.
Please note: The companies we buy from are in the process of updating their prices for 2023. Prices on our website are subject to change at this time. Dismiss