new layout
warning: this is not how to include the shop layout in a page, please read docs
Preview
Filtering by
The AR-1 is used to power special configurations of track such as below. Track configuration like below would cause a short circuit if connected without the use of an AR-1. Note that if you follow Rail ’A’ around you will notice that it connects to Rail ‘B’! That is just like putting a piece of metal across Rail ’A’ and Rail ‘B’ which would cause a short circuit and would cause a power supply to shut down. The solution to power special track configurations like below is to add insulation gaps and power the sections with an AR-1. The AR-1 can also be used to isolate small sections of track, limiting the impact of short circuits if derailments occur to just one area of your layout.
Features: All Solid State Design Simple Connection with Only 4 Wires No Adjustments Necessary Provides Short Circuit Isolation for a Section of Track Status Indicator Light Fast and Secure Spring Clamp Connecters Fully Enclosed Circuit Board Electronics Size: 4.60 x 3.00 x 1.18 inches
Our all solid state design has many advantages over relay based designs. With the relay based designs we tested you could see the locomotive jerk when it crossed the gap at slow speeds. With our AR-1 we saw no visible change in speed at all! Further, compared to relay based designs, solid state units are far less likely to fail, switch many times faster and all without that annoying relay clicking sound.
$31.95
The CB-1 is used to divide the output of a power supply to isolate small sections of track, limiting the impact of short circuits if derailments occur to just one area of your layout. Add multiple CB-1 to isolate several sections of track.
Features:
All Solid State Design
Simple Connection with Only 4 Wires
No Adjustments Necessary
Provides Short Circuit Isolation for a Section of Track
Status Indicator Light
Fast and Secure Spring Clamp Connecters
Fully Enclosed Circuit Board Electronics
Size: 4.60 x 3.00 x 1.18 inches
$31.95
Features
- Contains 10 Bulbs
- Dimensions: 2.4mm Diameter, 8in. Insulated Wire Leads
- Average Life Cycle: 5000 Hours
$19.60
3-wire servo extension cable 12" (30cm) long, 24 AWG stranded wire. Added to the 12" cord that comes with most standard size servos you can power a switch up to 2 feet from an Octopus or Quad Servo board. Set of 1 cable.
$1.95
Product details |
|
|---|---|
| Bolt Depot Product #: | 9618 |
| Units: | US |
| Category: | Machine screws |
| Subcategory: | Machine screws |
| Head style: | Pan |
| Drive type: | Phillips |
| Material: | Stainless steel |
| Grade: | 18-8 |
| Thread density: | Coarse |
| Diameter: | #2 |
| Thread count: | 56 |
| Length: | 9/16" |
| Thread direction: | Right hand |
| Dimensional standard: | ASME B18.6.3 |
| Diameter in inches: | 0.086" |
| Head height Min: | 0.053" |
| Head height Max: | 0.062" |
| Head diameter Min: | 0.155" |
| Head diameter Max: | 0.167" |
| Drive size: | #1 |
$0.10
Product details |
|
|---|---|
| Bolt Depot Product #: | 7654 |
| Units: | US |
| Category: | Machine screws |
| Subcategory: | Machine screws |
| Head style: | Pan |
| Drive type: | Phillips |
| Material: | Stainless steel |
| Grade: | 18-8 |
| Thread density: | Coarse |
| Diameter: | #2 |
| Thread count: | 56 |
| Length: | 7/16" |
| Thread direction: | Right hand |
| Dimensional standard: | ASME B18.6.3 |
| Diameter in inches: | 0.086" |
| Head height Min: | 0.053" |
| Head height Max: | 0.062" |
| Head diameter Min: | 0.155" |
| Head diameter Max: | 0.167" |
| Drive size: | #1 |
$0.10
Product details |
|
|---|---|
| Bolt Depot Product #: | 7652 |
| Units: | US |
| Category: | Machine screws |
| Subcategory: | Machine screws |
| Head style: | Pan |
| Drive type: | Phillips |
| Material: | Stainless steel |
| Grade: | 18-8 |
| Thread density: | Coarse |
| Diameter: | #2 |
| Thread count: | 56 |
| Length: | 5/16" |
| Thread direction: | Right hand |
| Dimensional standard: | ASME B18.6.3 |
| Diameter in inches: | 0.086" |
| Head height Min: | 0.053" |
| Head height Max: | 0.062" |
| Head diameter Min: | 0.155" |
| Head diameter Max: | 0.167" |
| Drive size: | #1 |
$0.10
The Blunami BLU-2200
The BLU-2200 is a universal-style sound decoder that can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. This decoder is suitable for use in both HO and small S-scale models. Wireless mode not currently available for android devices.
DYNAMIC DIGITAL EXHAUST
For added realism, you’ll love our reactive Dynamic Digital Exhaust (DDE) feature that automatically notches your models engine up or down depending on the load on the motor. With the Blunami App, DDE calibration has never been easier. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Blunami the ability to create the most realistic experience possible.
HIGH QUALITY SOUND LIBRARY
Our large selection of high quality sound effects include:
- 10 Exhaust Chuffs
- Up to 12 Prime Movers in each sound profile
- Up to 12 Bells
- 90 Whistles
- 40+ Airhorns
- Additional couplers, dynamos, cab chatter and more!
| Dimensions: | 41.9 x 18.8 x 6.8mm |
| Max. Motor Stall Current: | 2A |
| Max. Function Current: | 100mA (each output) |
| Function Outputs: | 6 |
| Audio Amplifier: | 2 Watt, 8-Ohm Load |
| DCC Track Voltage: | 7.5V – 22V |
| Sound Channels: | 16 |
$135.96
The Blunami BLU-2200
The BLU-2200 is a universal-style sound decoder that can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. This decoder is suitable for use in both HO and small S-scale models. Wireless mode not currently available for android devices.
DYNAMIC DIGITAL EXHAUST
For added realism, you’ll love our reactive Dynamic Digital Exhaust (DDE) feature that automatically notches your models engine up or down depending on the load on the motor. With the Blunami App, DDE calibration has never been easier. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Blunami the ability to create the most realistic experience possible.
HIGH QUALITY SOUND LIBRARY
Our large selection of high quality sound effects include:
- 10 Exhaust Chuffs
- Up to 12 Prime Movers in each sound profile
- Up to 12 Bells
- 90 Whistles
- 40+ Airhorns
- Additional couplers, dynamos, cab chatter and more!
| Dimensions: | 41.9 x 18.8 x 6.8mm |
| Max. Motor Stall Current: | 2A |
| Max. Function Current: | 100mA (each output) |
| Function Outputs: | 6 |
| Audio Amplifier: | 2 Watt, 8-Ohm Load |
| DCC Track Voltage: | 7.5V – 22V |
| Sound Channels: | 16 |
$135.96
The Blunami BLU-2200
The BLU-2200 is a universal-style sound decoder that can be operated in three different ways: DC, DCC and Wireless mode. Using the Blunami app (iOS versions 8 or later), you can operate your locomotive with incredible ease of use. This decoder is suitable for use in both HO and small S-scale models. Wireless mode not currently available for android devices.
DYNAMIC DIGITAL EXHAUST
For added realism, you’ll love our reactive Dynamic Digital Exhaust (DDE) feature that automatically notches your models engine up or down depending on the load on the motor. With the Blunami App, DDE calibration has never been easier. When your locomotive is traveling across flat terrain and simply maintaining speed, you will hear your locomotive chugging along. But, when the locomotive encounters a grade and the engineer applies more throttle to get the train up the hill, the engine sounds will automatically react and reflect the increase of power needed to crest the hill. DDE accomplishes this by calculating the changes in strain or load on the motor and adjusting the exhaust to appropriately simulate the work the engineer would be doing to the throttle of the engine. This gives Blunami the ability to create the most realistic experience possible.
HIGH QUALITY SOUND LIBRARY
Our large selection of high quality sound effects include:
- 10 Exhaust Chuffs
- Up to 12 Prime Movers in each sound profile
- Up to 12 Bells
- 90 Whistles
- 40+ Airhorns
- Additional couplers, dynamos, cab chatter and more!
| Dimensions: | 41.9 x 18.8 x 6.8mm |
| Max. Motor Stall Current: | 2A |
| Max. Function Current: | 100mA (each output) |
| Function Outputs: | 6 |
| Audio Amplifier: | 2 Watt, 8-Ohm Load |
| DCC Track Voltage: | 7.5V – 22V |
| Sound Channels: | 16 |
$135.96
How to install
You can now add layouts you create in the Shop Admin into any post or page. To make it simple a Shortcode Generator is included. You can access it via this button.
The first button is the shortcode genreator launcher and the second one ( the one with a plus ) ads a single audio player to the page from the media gallery.
